YOUR PLUMBING CRASH COURSE: WHAT YOU MUST HAVE FOR BATHTUB INSTALLATION

Your Plumbing Crash Course: What You Must Have for Bathtub Installation

Your Plumbing Crash Course: What You Must Have for Bathtub Installation

Blog Article

Call

The publisher is making a number of great pointers related to How to Install a Bathtub Yourself as a whole in the article below.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bath tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately challenging project. If the old bathtub is readily available, the project can relocate easily; if you have to open up a wall surface to get rid of the old tub and position the new bath tub, the job is much harder. In either case, the project is within a residence handyman's skills, although you will need an assistant to leave the old tub and also set in the new one. Ensure you have actually certified on your own for the job as well as fit trying it. Rather than working with a professional to take over a halfway-completed project, it is far better to take into consideration utilizing one prior to you start. Possibilities are you may require an expert plumber to make tube links.
This post will help you set up a new tub in your restroom if you have actually currently gotten a new bathtub and also do not require to alter the setup of your previous water system pipes.
Your tools and product list must consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be quite troublesome because of the limited gain access to that is often the case.
    Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
    Before going on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will need a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
    If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area between the tap and the sink. Protect the tap in position with the maker provided backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap ports. The previous type needs to be attached to the faucet finishes initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Installing the Bathtub


    Utilizing both wooden boards under its feet, place the bath tub in the required setting. The wood boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little points.
    The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the tub until the spirit level checks out degree.
    To mount taps, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
    Switch on the supply of water as well as examine all joints and also brand-new pipework for leakages and tighten them if required. Load the tub and also check the overflow outlet and also the regular outlet for leaks.
    Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bath tub must wait till the tub has actually been made use of a minimum of once as this will certainly resolve it into its last placement.

    Planning for the Setup


    To start with, the supporting structure supplied with the bath needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets unit to avoid strain on the bathtub.
    Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of all of the provided washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last placement.

    Tiling Around the Bathtub


    In the location where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, triggering the water to penetrate the wall between the bath and also the tiling, causing complications with dampness and also feasible leaks to the ceiling listed below.
    You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and also cartridges, and also are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can break fairly early if you do not think about this motion before securing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant glue and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I ran across that piece of writing on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the web. You should set aside a second to share this blog post if you liked it. We love reading our article about Installing A Bathtub.


    Damage control? Ring!

    Report this page